Cisco router 871 fe konfiguration
Hallo zusammen,
ich letzte woche ein projektarbeit an der FH angefangen, und habe keine erfahrung mit cisco router...
also ich habe ein router 871er und ein lapi an der Hand gedrückt bekommen und wurde mir gesagt, ich muss für den anfang die switchports für IPV6 konfigurieren, also 4 Ports=4client.. es besteht noch keine verbindung zur Modem oder Internet (wan kommt erst später).
ich habe also so angefangen na bissel googeln natürlich :
habe ich das richtig gemacht??
fals ja wie soll ich noch fort fahren?
kann ich alle 4 switchports einem vlan zuweisen oder muss ich ja für jeden eins einrichten? "ich denke eins reicht "
die link- oder site-local adressen kann ich frei wählen ist das richtig?
ich habe für euch auch die Version kopiert:
ich bin für jed tipp oder hilfe dankbar...
MFG
nonoboy
ich letzte woche ein projektarbeit an der FH angefangen, und habe keine erfahrung mit cisco router...
also ich habe ein router 871er und ein lapi an der Hand gedrückt bekommen und wurde mir gesagt, ich muss für den anfang die switchports für IPV6 konfigurieren, also 4 Ports=4client.. es besteht noch keine verbindung zur Modem oder Internet (wan kommt erst später).
ich habe also so angefangen na bissel googeln natürlich :
yourname(config)#ipv6 unicast-routing
yourname(config)#interface fastethernet 0
yourname(config-if)#switch mode access
yourname(config-if)#switch access vlan 1
yourname(config-if)#exit
yourname(config)#int
yourname(config)#interface vlan1
yourname(config-if)#ipv6 address FE80::AAB1:D4FF:FEC2:BF1F link-local (frei gewählt)
yourname(config-if)#no shutdown
yourname(config-if)#exit
yourname(config)#exit
yourname#write memory
fals ja wie soll ich noch fort fahren?
kann ich alle 4 switchports einem vlan zuweisen oder muss ich ja für jeden eins einrichten? "ich denke eins reicht "
die link- oder site-local adressen kann ich frei wählen ist das richtig?
ich habe für euch auch die Version kopiert:
Cisco IOS Software, C870 Software (C870-ADVIPSERVICESK9-M), Version 12.4(15)T13,
RELEASE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Wed 07-Apr-10 19:07 by prod_rel_team
ROM: System Bootstrap, Version 12.3(8r)YI4, RELEASE SOFTWARE
yourname uptime is 3 hours, 10 minutes
System returned to ROM by power-on
System image file is "flash:c870-advipservicesk9-mz.124-15.T13.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
export@cisco.com.
Cisco 871 (MPC8272) processor (revision 0x300) with 118784K/12288K bytes of memo
ry.
Processor board ID FCZ142690TQ
MPC8272 CPU Rev: Part Number 0xC, Mask Number 0x10
5 FastEthernet interfaces
128K bytes of non-volatile configuration memory.
24576K bytes of processor board System flash (Intel Strataflash)
Configuration register is 0x2102
MFG
nonoboy
Please also mark the comments that contributed to the solution of the article
Kommentar vom Moderator Dani am May 09, 2011 um 14:28:50 Uhr
Verschoben von Linux nach Netwerk.
Formatierungshilfen eingefügt.
Formatierungshilfen eingefügt.
Content-Key: 165919
Url: https://administrator.de/contentid/165919
Printed on: April 23, 2024 at 18:04 o'clock
9 Comments
Latest comment
Du kannst die L2 Switchports wahlfrei VLAN (Layer 3 Inerfaces) zuordnen. Letztlich funktioniert das wie bei einem Cisco Switch auch so was die LAN Ports anbetrifft.
Deine Konfig ist also soweit absolut richtig ! ggf. solltest du auf dem interface fastethernet 0 auch noch einen "no shut" fahren falls dieses im shutdown state sein soll.
Das Kommando "show int" zeigt dir das an.
Siehe auch: Cisco 880, 890 und ISR Router Konfiguration mit xDSL, Kabel oder FTTH Anschluss plus VPN und IP-TV
Deine Konfig ist also soweit absolut richtig ! ggf. solltest du auf dem interface fastethernet 0 auch noch einen "no shut" fahren falls dieses im shutdown state sein soll.
Das Kommando "show int" zeigt dir das an.
Siehe auch: Cisco 880, 890 und ISR Router Konfiguration mit xDSL, Kabel oder FTTH Anschluss plus VPN und IP-TV
Du hast aber scheinbar an FE0 und an FE1 physisch nichts angeschlossen, denn wie du sehen kannst ist dein Line Protocoll Down, sprich der Router sieht keinen aktiven Link dort !!
Wenn du NUR das VLAN 1 hast, dann musst du nichts unter den Fast Ethernet Ports definieren, denn dann sind sie automatisch im default VLAN 1 !!
Eine simple v4 Konfig sähe dann so aus:
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description Externes Netzwerk / WAN Port
ip address 10.66.79.73 255.255.255.224
!
interface Vlan1
description Loakles Netzwerk LAN (FE0 bis FE3)
ip address 10.0.0.254 255.255.255.0
!
Fertisch....
Am besten du postets mal ein "show run" hier damit man sehen kann was du da verbrochen hast in der Router Config....
Wenn du NUR das VLAN 1 hast, dann musst du nichts unter den Fast Ethernet Ports definieren, denn dann sind sie automatisch im default VLAN 1 !!
Eine simple v4 Konfig sähe dann so aus:
!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
!
interface FastEthernet3
!
interface FastEthernet4
description Externes Netzwerk / WAN Port
ip address 10.66.79.73 255.255.255.224
!
interface Vlan1
description Loakles Netzwerk LAN (FE0 bis FE3)
ip address 10.0.0.254 255.255.255.0
!
Fertisch....
Am besten du postets mal ein "show run" hier damit man sehen kann was du da verbrochen hast in der Router Config....
Ääääähhh ja.... mehr oder weniger wenn man jetzt wüsste was du vorhast ?!
Auf FE4 fehlen schon die minimalsten Basiscs damit das zum Fliegen kommt !!
Nämlich eine IPv4 IP Adresse UND auch eine IPv6 IP Adresse !!!
Zudem ist das Interface noch auf "shutdown" also physisch deaktiviert !!! Das musst du logischerweise ändern damit es klappen soll !
Als allererstes also folgende Schritte:
yourname#conf t
yourname(config)#interface FastEthernet4
yourname(config-int)#ip address x.x.x.x m.m.m.m
yourname(config-int)#ipv6 address xxxx:xxxx....
yourname(config-int)#no shutdown
yourname(config-int)#exit
yourname(config)#exit
yourname#wr
Statische Routen wie du sie oben versuchst sind Blödsinn und überflüssig, denn der Router "kennt"" ja seine IP Netze da sie direkt an ihm angeschlossen sind !
Das kannst du also weglassen !!
Auf FE4 fehlen schon die minimalsten Basiscs damit das zum Fliegen kommt !!
Nämlich eine IPv4 IP Adresse UND auch eine IPv6 IP Adresse !!!
Zudem ist das Interface noch auf "shutdown" also physisch deaktiviert !!! Das musst du logischerweise ändern damit es klappen soll !
Als allererstes also folgende Schritte:
yourname#conf t
yourname(config)#interface FastEthernet4
yourname(config-int)#ip address x.x.x.x m.m.m.m
yourname(config-int)#ipv6 address xxxx:xxxx....
yourname(config-int)#no shutdown
yourname(config-int)#exit
yourname(config)#exit
yourname#wr
Statische Routen wie du sie oben versuchst sind Blödsinn und überflüssig, denn der Router "kennt"" ja seine IP Netze da sie direkt an ihm angeschlossen sind !
Das kannst du also weglassen !!