v-fsi09
Goto Top

Cisco Catalyst 2900 VLAN fähig?

Hi,

ich wollte beim Cisco Switch Catalyst 2900 XL VLANs einrichten.
Leider bekomme ich die Befehle, die dafür notwendig sind (z.B. switchport) nicht zur Auswahl.
Habe es wie folgt versucht:

conf t
int fa0/3
switchport ?
% Unrecognized command

Zur Info ein Auszug aus sh version:
Cisco Internetwork Operating System Software
IOS (tm) C2900XL Software (C2900XL-H-M), Version 11.2(8)SA2, RELEASE SOFTWARE (fc1)

Dachte vielleicht bringt ein IOS Update etwas, allerdings kennt der Switch den Befehl sh flash ebenfalls nicht.

Default VLAN ist vorhanden. Ausgabe von sh int:
VLAN1 is up, line protocol is up
Hardware is CPU Interface, address is 0090.b198.8540 (bia 0090.b198.8540)
Internet address is 192.168.2.199/24
MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255
Encapsulation ARPA, loopback not set, keepalive not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:30:19, output hang never
Last clearing of "show interface" counters never
Queueing strategy: fifo
Output queue 0/40, 0 drops; input queue 0/75, 0 drops
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 input packets with dribble condition detected
42 packets output, 2520 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out


Weiß jemand woran das liegen könnte und was ich jetzt tun kann?

Wäre euch sehr dankbar!

Grüße
V-FSI09

Content-Key: 134542

Url: https://administrator.de/contentid/134542

Ausgedruckt am: 29.03.2024 um 12:03 Uhr

Mitglied: brammer
brammer 28.01.2010 um 08:16:19 Uhr
Goto Top
Hallo,

der von dir verwendete IOS Befehl wurde erst eine IOS Verison später impementiert!
Das heißt für dich das IOS updaten!

http://www.cisco.com/en/US/docs/switches/lan/catalyst2900xl_3500xl/rele ...

brammer
Mitglied: aqui
aqui 28.01.2010, aktualisiert am 18.10.2012 um 18:40:59 Uhr
Goto Top
Er ist aber damit uneingeschränkt VLAN fähig!
Beispielkonfigs siehst du hier:
VLAN Installation und Routing mit pfSense, Mikrotik, DD-WRT oder Cisco RV Routern
und hier:
VLANs über 802.1q Trunk auf Windows und Linux Rechnern realisieren
zum Beispiel...
Mitglied: brammer
brammer 28.01.2010 um 12:48:08 Uhr
Goto Top
Hallo,

ja, VLAN fähig ist der Switch trotzdem...

Nur wird das nachstellen und überprüfen einer konfigruation schwierig
wenn die Befehle nicht akzeptiert werden da die IOS version veraltet ist.

brammer
Mitglied: V-FSI09
V-FSI09 28.01.2010 um 15:25:14 Uhr
Goto Top
Hallo.

Gibt es eine andere Möglichkeit das IOS upzudaten,
weil bei mir geht der befehl show flash nicht, um mir den Namen des Images anzeigen zu lassen,
damit ich es vorher sichern und anschließend löschen kann?

Ist schon seltsam, ich bekomme mit sh int vlan 1 als up angezeigt, habe aber keine VLAN Befehle zur Auswahl.

Danke!
Mitglied: brammer
brammer 28.01.2010 um 16:43:03 Uhr
Goto Top
Hallo,

wennn sh flash nicht geht, teste mal sh version.

im übrigen kannst du dich jederzeit mit "show ?" durch hangeln.
Das heißt eigentlich geht das "?" bei jedem Befehl und auch das Vervollständigen eines Befehls mit der Tabulatortaste ist manchmal hilfreich.

brammer
Mitglied: V-FSI09
V-FSI09 28.01.2010 um 19:26:32 Uhr
Goto Top
Hi,

sh version
funktioniert, allerdings erhalte ich da keine Infos über den Namen des Images. Dies ist glaub ich nur mit sh flash möglich.
Das mit dem "?" ist mir bekannt. Konnte auch nichts ähnliches anstatt "flash" oder unter int fa 0/x "switchport" finden.

Folgende Befehle habe ich zur Auswahl:
Cisco Internetwork Operating System Software
IOS (tm) C2900XL Software (C2900XL-H-M), Version 11.2(8)SA2, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1998 by cisco Systems, Inc.
Compiled Fri 24-Apr-98 10:51 by rheaton
Image text-base: 0x00003000, data-base: 0x001A582C

ROM: Bootstrap program is C2900XL boot loader

Switch uptime is 1 hour, 15 minutes
System restarted by power-on
Running default software


cisco WS-C2924-XL (PowerPC403GA) processor (revision 0x11) with 4096K/1024K bytes of memory.
Processor board ID FAA0238Z0EN, with hardware revision 0x00
Board ID 0x07
Last reset from power-on
24 Ethernet/IEEE 802.3 interface(s)

32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:90:B1:98:85:40
Configuration register is 0xF

Switch#?
Exec commands:
access-enable Create a temporary Access-List entry
access-template Create a temporary Access-List entry
cd Change current directory
clear Reset functions
clock Manage the system clock
configure Enter configuration mode
connect Open a terminal connection
copy Copy from one file to another
debug Debugging functions (see also 'undebug')
delete Delete a file
dir List files on a filesystem
disable Turn off privileged commands
disconnect Disconnect an existing network connection
enable Turn on privileged commands
exit Exit from the EXEC
format Format a filesystem
fsck Fsck a filesystem
help Description of the interactive help system
lock Lock the terminal
login Log in as a particular user
logout Exit from the EXEC
mkdir Create new directory
more Display the contents of a file
name-connection Name an existing network connection
no Disable debugging functions
ping Send echo messages
pwd Display current working directory
reload Halt and perform a cold restart
rename Rename a file
resume Resume an active network connection
rmdir Remove existing directory
rsh Execute a remote command
send Send a message to other tty lines
setup Run the SETUP command facility
show Show running system information
systat Display information about terminal lines
tar List or extract files in a tar image
telnet Open a telnet connection
terminal Set terminal line parameters
test Test subsystems, memory, and interfaces
traceroute Trace route to destination
tunnel Open a tunnel connection
undebug Disable debugging functions (see also 'debug')
where List active connections
write Write running configuration to memory, network, or terminal


Es gibt nicht einmal erase ... (startup-config)..

Hat jemand eine Idee?
Mitglied: brammer
brammer 28.01.2010 um 20:50:58 Uhr
Goto Top
Hallo,


sh version
funktioniert, allerdings erhalte ich da keine Infos über den Namen des Images. Dies ist glaub ich nur mit sh flash möglich.
Das mit dem "?" ist mir bekannt. Konnte auch nichts ähnliches anstatt "flash" oder unter int fa 0/x "switchport" finden.

Ist ja schon mal ein Fortschritt.


Wer Lesen kann ist klar imVorteil :

IOS (tm) C2900XL Software (C2900XL-H-M), Version 11.2(8)SA2, RELEASE SOFTWARE (fc1)

Das ist doch deine IOS Version!

Cisco 2900 ist übrigens eine Baureihe, du bist Stolzer Besitzer eines 2924 XL Switches:
cisco WS-C2924-XL (PowerPC403GA) processor (revision 0x11) with 4096K/1024K bytes of memory.
Processor board ID FAA0238Z0EN, with hardware revision 0x00

Habe mal die wichtigsten Befehle rausgezogen:

configure Enter configuration mode
Hast du mal versucht im config Mode ein VLAN anzulegen oder immer nur im enable mode?

delete Delete a file
Selbsterklärend

dir List files on a filesystem
Vielleicht noch aus dem DOS bekannt.

enable Turn on privileged commands
Hast du ja schonrausgefunden

exit Exit from the EXEC
selbsterklärend

help Description of the interactive help system
Kennst du ja schon

ping Send echo messages
selbst erklärend

reload Halt and perform a cold restart
Neustart, anstatt immer das Kabel zu ziehen.

rename Rename a file
Dateien löschen ist manchmal nicht gut, umbenennnen recht doch

traceroute Trace route to destination
Sollte bekannt sein.

write Write running configuration to memory, network, or terminal
speichern..


Es gibt nicht einmal erase ... (startup-config)..
mal im config mode ein "?" eingegeben?

Hat jemand eine Idee?
Tausende

brammer
Mitglied: V-FSI09
V-FSI09 28.01.2010 um 21:06:07 Uhr
Goto Top
OK, anscheinend habe ich mich nicht klar ausgedrückt gehabt. Sorry.

Ich hab nicht die IOS Version gesucht sondern den Namen des Images, welches normal mit
sh flash angezeigt wird, damit ich es sichern kann, bevor ich das Update durchführe.

Switch#dir
%Error parsing (No such device)
Weiß nicht ob das normal ist?

Die Befehle sind mir klar, ich habe desöfteren mit Cisco Routern / Switches zu tun gehabt und auch schon VLANs eingerichtet.
? im Config mode habe ich natürlich auch probiert.
Sogar im int Fax/x mode. Deshalb konnte ich ja die Aussage geben, das keine VLAN Befehle zur Auswahl stehen.
Mitglied: aqui
aqui 29.01.2010 um 02:01:18 Uhr
Goto Top
Wenn dann dir flash: ! Das ein show flash nicht funktioniert ist schon mehr als ungewöhnlichen, denn das können alle Ciscos schon seit Kindertagen !
Warum datest du nicht up auf das aktuellste IOS für diese HW http://tools.cisco.com/support/downloads/pub/Redirect.x?mdfid=268438038 ?
Sichern musst du nicht unbedingt, denn auch bei Problemen kannst du immer alles recovern über den Bootloader !
Mitglied: V-FSI09
V-FSI09 21.07.2010 um 16:34:43 Uhr
Goto Top
Dieser Switch kann glaub ich leider nur ISL VLAN und nicht den Standard 802.1q