Cisco 866VAE verliert nach IOS Upgrade von 15.3.x auf 15.4.x oder höher ständig die PPP Verbindung
Hallo Zusammen,
wir verwenden einen Cisco 866VAE auf dem aktuell folgende Software läuft (c860vaew-advsecurityk9-mz.SPA.153-3.M6.bin):
IOS Version:
Cisco IOS Software, C860 Software (C860VAEW-ADVSECURITYK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Modem:
Modem FW Version:4.12L.08, Modem PHY Version: B2pvF037f2.d24g1, Vendor Version: bcm963268_4.12L.08
Nun wollte ich vor einigen Tagen die Software einmal auf den aktuellen Stand bringen und habe mit der aktuellsten Version das Problem, daß
Folgendes dazu im Log:
*Dec 30 22:42:54.775: Vi1 PPP: Missed 5 keepalives, taking LCP down
*Dec 30 22:42:54.775: Vi1 PPP DISC: Missed too many keepalives
*Dec 30 22:42:54.775: Vi1 PPP: Sending Acct Event[Down] id[54]
*Dec 30 22:42:54.775: PPP: NET STOP send to AAA.
*Dec 30 22:42:54.775: Vi1 IPCP: Event[DOWN] State[Open to Starting]
*Dec 30 22:42:54.775: Vi1 IPCP: Event[CLOSE] State[Starting to Initial]
*Dec 30 22:42:54.775: Vi1 LCP: O TERMREQ [Open] id 2 len 4
*Dec 30 22:42:54.775: Vi1 LCP: Event[CLOSE] State[Open to Closing]
*Dec 30 22:42:54.775: Vi1 PPP: Phase is TERMINATING
*Dec 30 22:42:54.775: Vi1 LCP: Event[DOWN] State[Closing to Initial]
*Dec 30 22:42:54.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down
*Dec 30 22:42:54.775: Vi1 PPP: Phase is DOWN
*Dec 30 22:42:54.783: Di1 Deleted neighbor route from AVL tree: topoid 0, address xxx.xxx.xxx.xxx
*Dec 30 22:42:54.783: Di1 IPCP: Remove route to xxx.xxx.xxx.xxx
*Dec 30 22:42:54.783: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di1
*Dec 30 22:42:54.787: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Das Problem kann ich nachvollziehen ab dieser IOS Version:
c860vaew-advsecurityk9-mz.SPA.154-3.M8.bin
Die 15.3.x liefen alle problemlos.
Die Config sieht so aus:
Betrieben wird das Ganze an einem VDSL25 Anschluss der Telekom.
Vielen Dank im Voraus für eure Hilfe.
wir verwenden einen Cisco 866VAE auf dem aktuell folgende Software läuft (c860vaew-advsecurityk9-mz.SPA.153-3.M6.bin):
IOS Version:
Cisco IOS Software, C860 Software (C860VAEW-ADVSECURITYK9-M), Version 15.3(3)M6, RELEASE SOFTWARE (fc1)
Modem:
Modem FW Version:4.12L.08, Modem PHY Version: B2pvF037f2.d24g1, Vendor Version: bcm963268_4.12L.08
Nun wollte ich vor einigen Tagen die Software einmal auf den aktuellen Stand bringen und habe mit der aktuellsten Version das Problem, daß
- gar kein VDSL Sync klappt -> behoben durch die Verwendung von "ppp packet throttle 50 5 30"
- das PPP Interface nach kurzer Zeit einen shutdown macht und danach wieder aufgebaut wird (was aber nicht wirklich von langer dauer ist und wieder down usw.)
Folgendes dazu im Log:
*Dec 30 22:42:54.775: Vi1 PPP: Missed 5 keepalives, taking LCP down
*Dec 30 22:42:54.775: Vi1 PPP DISC: Missed too many keepalives
*Dec 30 22:42:54.775: Vi1 PPP: Sending Acct Event[Down] id[54]
*Dec 30 22:42:54.775: PPP: NET STOP send to AAA.
*Dec 30 22:42:54.775: Vi1 IPCP: Event[DOWN] State[Open to Starting]
*Dec 30 22:42:54.775: Vi1 IPCP: Event[CLOSE] State[Starting to Initial]
*Dec 30 22:42:54.775: Vi1 LCP: O TERMREQ [Open] id 2 len 4
*Dec 30 22:42:54.775: Vi1 LCP: Event[CLOSE] State[Open to Closing]
*Dec 30 22:42:54.775: Vi1 PPP: Phase is TERMINATING
*Dec 30 22:42:54.775: Vi1 LCP: Event[DOWN] State[Closing to Initial]
*Dec 30 22:42:54.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Virtual-Access1, changed state to down
*Dec 30 22:42:54.775: Vi1 PPP: Phase is DOWN
*Dec 30 22:42:54.783: Di1 Deleted neighbor route from AVL tree: topoid 0, address xxx.xxx.xxx.xxx
*Dec 30 22:42:54.783: Di1 IPCP: Remove route to xxx.xxx.xxx.xxx
*Dec 30 22:42:54.783: %DIALER-6-UNBIND: Interface Vi1 unbound from profile Di1
*Dec 30 22:42:54.787: %LINK-3-UPDOWN: Interface Virtual-Access1, changed state to down
Das Problem kann ich nachvollziehen ab dieser IOS Version:
c860vaew-advsecurityk9-mz.SPA.154-3.M8.bin
Die 15.3.x liefen alle problemlos.
Die Config sieht so aus:
controller VDSL 0
operating mode vdsl2
!
interface ATM0
no ip address
shutdown
atm ilmi-keepalive
pvc 1/32
!
!
interface Ethernet0
no ip address
!
interface Ethernet0.1
description PrimaryWANDesc_
encapsulation dot1Q 7
pppoe-client dial-pool-number 1
no cdp enable
!
Betrieben wird das Ganze an einem VDSL25 Anschluss der Telekom.
Vielen Dank im Voraus für eure Hilfe.
Please also mark the comments that contributed to the solution of the article
Content-Key: 359773
Url: https://administrator.de/contentid/359773
Printed on: April 24, 2024 at 03:04 o'clock
2 Comments
Latest comment
Cisco 880, 890 und ISR Router Konfiguration mit xDSL, Kabel oder FTTH Anschluss plus VPN und IP-TV
Da hast du schon drüber geschaut?
Da hast du schon drüber geschaut?