emjott
Goto Top

HP Designjet 1050 Netzwerkeinstellung ändern

Ich muss bei einem HP Designjet 1050 die IP-Adresse anpassen und bekomme es nicht hin. Im Druckermenu gibt es zwar einen Punkt Netzwerkeinstellungen, doch dort kann man nichts einstellen. Stattdessen wird auf Printer und in dem Handbuch auf Programm "Jet...." verwiesen.

Tolles Ding... habe eben noch was bei HP gefunden. Werde mal die Tage testen ob das so geht...Bis zum Punkt 6. kam ich schonmal ^^

1. Press TOP, and then press ENTER.
2. Press the DOWN arrow to I/O SETUP. Press ENTER.
3. Highlight NETWORK CARD, and then press ENTER.
4. Highlight CONFIGURATION, then press ENTER.
5. At Configure Network=NO, press ENTER.
6. Press the UP arrow to change to Configure Network=Yes, then press ENTER.
7. Press the UP arrow until the display reads Configure=TCP/IP NO, then press ENTER.
8. Press the UP arrow to change to Configure TCP/IP=YES, then press ENTER.
9. Press the UP arrow to BootP=YES, then press ENTER.
10. Press the UP arrow to change to BootP=NO, then press ENTER.
11. Press the UP arrow until IP Byte1=xxx appears.

12. To change the IP byte (the first octet of the IP address), proceed as follows:
12.1 Press ENTER. The top of the display will read Active Option.
12.2 Press the up or down arrow to change the number.
12.3 Press ENTER.
12.4 Press the up key to continue to IP Byte2=xxx.

13. Configure the subnet mask bytes (SM Byte), syslog server IP address (LG Byte), default gateway (GW Byte), and timeout (TIMEOUT) in the same manner. (Press ENTER to make the display read Active Option, press the up or down arrows to change the octet of the IP address, then press the ENTER key.)

Content-Key: 60234

Url: https://administrator.de/contentid/60234

Ausgedruckt am: 29.03.2024 um 07:03 Uhr

Mitglied: anteNope
anteNope 25.07.2020 aktualisiert um 15:31:54 Uhr
Goto Top
Oh mein Gott! Dieses Menü kommt direkt aus der Hölle! Ich hatte gerade das Vergnügen die IP-Adresse zu ändern.

Der Trick ist, dass der Eintrag "BootP" nur erscheint, wenn man mit der Pfeiltaste nach OBEN geht. Und dann muss man jedes Segment der IP Einzeln durchtippen, nach dem Schema: Byte1.Byte2.Byte3.Byte4 = 192.168.0.1

Und ja, es gibt noch Windows 10 Treiber für x64 und x86. Diese findet man im Microsoft Update-Catalog. Gibt zig Einträge für alle möglichen Sprachen und Betriebssystemversionen. Wenn man dann aber tatsächlich den passenden findet, funktioniert die Maschine einwandfrei!
Mitglied: beqbiq
beqbiq 16.10.2020 um 15:19:33 Uhr
Goto Top
ja, das muss aus der Hölle sein. Ich versuche mich schon seit 1 Stunde an dem Menü. Ich vermute das Teil grinst mich nur an. Wie hast Du das denn geschafft?
Mitglied: anteNope
anteNope 18.10.2020 um 13:10:46 Uhr
Goto Top
Also ob die Anleitung ist schon korrekt. Wenn du in Network bist, erscheint BootP NUR wenn du mit der Pfeiltaste nach oben gehst. Und dann ist das nur fummelige Fleißarbeit die Werte da rein zu kloppen. Am Ende das Teil neu starten und et voila, fertig.