4
WLAN unter windows 8 tablet ohne dhcp
Hallo zusammen,
ich habe mal eine blöde Frage:
Wie kann ich ein Windows 8 tablet in ein WLAN ohne dhcp hängen?
Das tablet meckert, ich sei offline. LAN hat es nicht.
Also WLAn. WLAN habe ich aber nur feste IPs.
Ich kann das WLAN in der Anmeldung auswählen und den Schlüssel eingeben. Aber keine IP zuweisen...
Wie krieg ich das Teil nun online? So kann ich mich nicht mal anmelden.
mfG
tsunami
ich habe mal eine blöde Frage:
Wie kann ich ein Windows 8 tablet in ein WLAN ohne dhcp hängen?
Das tablet meckert, ich sei offline. LAN hat es nicht.
Also WLAn. WLAN habe ich aber nur feste IPs.
Ich kann das WLAN in der Anmeldung auswählen und den Schlüssel eingeben. Aber keine IP zuweisen...
Wie krieg ich das Teil nun online? So kann ich mich nicht mal anmelden.
mfG
tsunami
Share on Facebook
Share on Twitter
Share on Reddit
Share on LinkedinPlease also mark the comments that contributed to the solution of the article
Content-Key: 236632
Url: https://administrator.de/contentid/236632
Printed on: April 20, 2024 at 02:04 o'clock
4 Comments
Latest comment
Windows 8 - Set up with a Static IP Address
Below are the steps for setting up your Windows 8 computer with a static IP address.
1.From the Start Menu (Tiles), open the Charms bar by moving the mouse to the right bottom corner of the screen or press the Windows Key + C and click on Search.
2.Highlight Settings.
3.In the Search box type Network to search for any network related options
4.From the list options choose Network and Sharing Center.
(Note: As an alternate option, you can also use Windows key+X from the Start Menu (Tiles) to open the "classic" menu and choose Control Panel, then choose Network and Sharing Center).
1.From the View Your Active Networks section, select Local Area Connection.
2.Go to Properties.
Result: The Local Area Connection Properties screen appears.
3.Highlight Internet Protocol Version 4 (TCP/IPv4) and click on Properties.
Result: The Internet Protocol Version 4 (TCP/IPv4) Properties screen appears.
4.Click Use the following IP address.
5.Complete the configuration fields as shown below. This part of the configuration requires attention to detail, because one error will prevent you from getting on the network. Be sure you have this information at hand when you start to configure the TCP/IP protocol: •IP Address: 18.x.y.z (where x,y, and z are numbers)
•Subnet mask: 255.255.0.0
•Default gateway: 18.x.0.1 (Where x matches the x in your IP address)
•DNS (Domain Name Servers): 18.71.0.151, 18.70.0.160, 18.72.0.3
6.Enter these numbers in the appropriate fields and click OK.
7.Continue to click OK or Close as appropriate until you return to the Network Connections screen. The Local Area Connection icon text should now say "Enabled".
8.Test your TCP/IP Settings: Launch your web browser. If you have completed the configuration successfully, the browser opens at your designated home page. If you have not completed the configuration, you will receive an error message that says that your browser was unable to connect properly. Go back and check your settings.
Below are the steps for setting up your Windows 8 computer with a static IP address.
1.From the Start Menu (Tiles), open the Charms bar by moving the mouse to the right bottom corner of the screen or press the Windows Key + C and click on Search.
2.Highlight Settings.
3.In the Search box type Network to search for any network related options
4.From the list options choose Network and Sharing Center.
(Note: As an alternate option, you can also use Windows key+X from the Start Menu (Tiles) to open the "classic" menu and choose Control Panel, then choose Network and Sharing Center).
1.From the View Your Active Networks section, select Local Area Connection.
2.Go to Properties.
Result: The Local Area Connection Properties screen appears.
3.Highlight Internet Protocol Version 4 (TCP/IPv4) and click on Properties.
Result: The Internet Protocol Version 4 (TCP/IPv4) Properties screen appears.
4.Click Use the following IP address.
5.Complete the configuration fields as shown below. This part of the configuration requires attention to detail, because one error will prevent you from getting on the network. Be sure you have this information at hand when you start to configure the TCP/IP protocol: •IP Address: 18.x.y.z (where x,y, and z are numbers)
•Subnet mask: 255.255.0.0
•Default gateway: 18.x.0.1 (Where x matches the x in your IP address)
•DNS (Domain Name Servers): 18.71.0.151, 18.70.0.160, 18.72.0.3
6.Enter these numbers in the appropriate fields and click OK.
7.Continue to click OK or Close as appropriate until you return to the Network Connections screen. The Local Area Connection icon text should now say "Enabled".
8.Test your TCP/IP Settings: Launch your web browser. If you have completed the configuration successfully, the browser opens at your designated home page. If you have not completed the configuration, you will receive an error message that says that your browser was unable to connect properly. Go back and check your settings.
Ah, Hallo, danke für die schnelle Antwort.
Ohne IP kann ich mich nicht anmelden. Also nichts mit Startmenü settings.
Vielleicht zur Verdeutlichung:
Windows 8 Installation bei x (tablet ohn LAN) im WLAN 123 mit DHCP
Das Teil mit nach Hause genommen -> WLAN 456 ohne DHCP
Ich kann das WLAN zwar auswählen aber keine IP Adresse vergeben...
Ohne IP kann ich mich nicht anmelden. Also nichts mit Startmenü settings.
Vielleicht zur Verdeutlichung:
Windows 8 Installation bei x (tablet ohn LAN) im WLAN 123 mit DHCP
Das Teil mit nach Hause genommen -> WLAN 456 ohne DHCP
Ich kann das WLAN zwar auswählen aber keine IP Adresse vergeben...
Versteh ich nicht wie kannst du das WLAN auswählen wenn du dich nicht anmelden kannst? Ist da ein VPN Client installiert?
Auf der rechten Seite werden die WLANs doch angezeigt. Doppelklick auf das gewünschte WLAN und dann den Key eingeben.
